Industrial PE Anti Corrosion Adhesive Tape

PE Anti-Corrosion Adhesive Tape

PE anticorrosive adhesive tape is mainly used in oil and gas transmission; Chemical industry, urban construction of water supply and drainage and gas transmission, etc. The outer surface of the buried steel pipeline corrosion. Construction is convenient, no pollution and other characteristics, is outside the pipe anticorrosion priority of anticorrosive system. The performance indicators of the product fully meet the provisions of CNPCstandard SY/T0414-2017 and American Industrial Association standards ANSI/AWWAC209-00 and NACEMR0274-95. The product has reached the level of similar products at home and abroad.

Inquiry now

product introduction

Performance advantage

1.Excellent adhesion to inner-layer tape and self

2.Resistant to UV

3.Can be applied over a wide temperature range

4.Good conformability and consistent uniform thickness

5.Easily applied with no special equipment

6.Compatible with common pipe coatings

7.Excellent resistance to cathodic disbonding

8.Meets ASTM D 1000 Standard

9.Cold applied

Structure:

Technical Parameters

Physical Properties		Test Method	Typical Value
Total thickness		ASTM D 1000	0.36-1.8mm
Width		-	50 -800 mm
Length		-	10 -240 m
Backing color		-	Black or others
Tensile strength		ASTM D 1000	≥50 N/ cm
Elongation		ASTM D 1000	≥300 %
Peel Adhesion to inner-layer tape	23℃	ASTM D 1000	≥0.2N/mm
	50℃		≥0.2N/mm
Storage Requirement		-	Suitable for storage at ambient temperatures ranging up to 40 ℃ with 90% humidity
Dielectric Strength		ASTM D 149	≥40 Kv
Volume Resistivity		ASTM D 257	≥1x1012 ohm.cm
Water Absorptivity		ASTM D 570	≤0.08%
Water Vapor Transmission Rate（24h）		ASTM F1249	≤0.01g/100sq in/24h	≤0.1g/100sq mm/24h
UV resistance		-	Excellent
Application Temperature		-	-40℉-140℉	-40℃ - +60℃

Application scenarios


Anticorrosion construction of natural oil and gas pipeline

Leave A Message

If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Subject : PE Anti-Corrosion Adhesive Tape

Tags :

Related products

Visco-Elastic Self-adhesive Corrosion Protection Tape

Viscoelastic Anti-Corrosion Adhesive Tape

The viscoelastic anti-corrosion adhesive tape is an ideal anti-corrosion product. Widely used in corrosion prevention and repair of the anti-corrosion coating of oil and natural gas pipelines, repair of damaged 3PE anti-corrosion coating, and corrosion protection of irregular equipment such as flanges, valves and pumps. It has unique cold flow property and can repair itself during anti-corrosion and repairing process to achieve complete protection. Due to the excellent chemical resistance and no peel-off of the cathodic protection layer, the product can completely eliminate water intrusion and microbial corrosion and thus ensure unique long-term effect.

Primer for Anti-Corrosion Tape

The anticorrosive primer and PE anticorrosive tape together constitute the polyethylene cold wound anticorrosive system. Coated on the surface treatment of steel tube, can fill a small bump on the surface of the steel tube, and can increase the adhesive tape with sticky relay between steel tube, at the same time it is also a kind of excellent corrosion inhibitor.

Anticorrosive Coating for Towers

Anticorrosive coating for towers is a two-component, thick-type, one-side polyurethane acrylic coating with excellent weather resistance and long recoating performance. This product has both anti-corrosion, weather resistance in one, with excellent wear resistance, impact resistance, color retention and aging resistance.

Heat Shrink 3 Cores Breakout (1~36kV)

Applications：

Used to provide insulation protection for cable termination and straight joint.

64/110KV YJZGG Dry Insulated Gis Termination For 64/110kv Xlpe Cable

Dry GIS termination has composite structure of stress cone and epoxy sheath, making the surface of pre-fabricated stress cone clinged to the inner wall of epoxy sheath through spring assembly to reach reasonable interface pressure.