Waterproof Insulation Waterseal Mastic Tape KC80

◆ Continuous waterproofing.
◆ Highly self-fusing tape.
◆ Suitable for irregular shapes cable.
◆ Resistance to high/low temperature.
◆ Resistance to corrosion.
◆ Resistance to ozone, UV, xenon exposure.
◆ New formulation for insulation.
◆ Operation and installation easily.
◆ Excellent adhesion to copper, aluminum and cable jacket.

Inquiry now

product introduction

Cotran Brand KC80 waterseal mastic tape is a conformable self-fusing rubber electrical insulating and sealing tape. KC80 consists of ethylene propylene rubber (EPR) and butyl mastic adhesive. It has strong adhesion to copper, aluminum, and cable jackets. It provides excellent waterproofing performance and temperature stability at 90℃,and withstanding of overload temperature up to 130℃.

Insulation Mastic Tape

Applications

◆ Use for insulating, filling and moisture sealing in splices of all types of power cables and optical telecommunication cables. For primary insulation up to 1000 volts.
◆ Use for insulation and moisture sealing irregular shaped bus bar bolted connections
◆ Use for moisture sealing high or low voltage junction boxes and irregular splices.
◆ Moisture seal for power cable and wire connections
◆ Moisture seal for service drops
◆ Moisture seal for ground wire and rod connections

Test Parameters

No.	Test Item	Result	Test Method
1	Width	51mm	ASTM D4325
2	Thickness	1.65mm	ASTM D4325
3	Tensile Strength	1.29MPa	ASTM D4325
4	Elongation at Break	970%	ASTM D4325
5	Water absorption	0.16%	ASTM D570
6	DielectricStrength	26.5kV/mm	ASTM D1000
7	Volume resistivity	8.9x1015Ω.cm	ASTM D257
8	Adhesion (180° Steel plate)	78.4N/50mm	ASTM D1000
9	Heat exposure	Pass, 130°C	ASTM D4388
10	Ozone ageing	Pass	ASTM D4388
11	UV ageing	Pass	ASTM D4388
12	Xenon ageing	Pass	ASTM D4388

Installation

Cotran Brand KC80 waterseal mastic tape should be applied in half–lapped layers until desired insulation build up is reached.

Step 1 Wipe off the dusts on the splice area before wrapping.

Step 2 Remove the liner and stretch the tape to 1 to 2 times of its original length, apply the tape in 50%-lapped with mastic side toward area to the wrapped. Stretching the tape to 4 times of its original length is not recommended.

Step 3 Make sure there is 30mm to 50mm wrapping tape above both sides of the splice area.

Step 4 After KC80 waterseal mastic tape is applied, overwrapping COTRAN PVC insulation tape is recommended, apply 3 layers of COTRAN PVC insulation tape in a 50% overlapping with no tension. Make sure not to overstretch the PVC tape during installation.

Leave A Message

If you are interested in our products and want to know more details,please leave a message here,we will reply you as soon as we can.

Subject : Waterproof Insulation Waterseal Mastic Tape KC80

Tags :

Related products

Water Seal Mastic Self Adhesive Tape KC86

◆ Continuous waterproofing.

◆ Highly self-fusing tape.

◆ Suitable for irregular shapes cable.

◆ Resistance to high/low temperature.

◆ Resistance to corrosion.

◆ Resistance to ozone, UV, xenon exposure.

◆ New formulation for insulation.

◆ Operation and installation easily.

◆ Excellent adhesion to copper, aluminum and cable jacket.

Super Thin Waterproof Waterseal Mastic Tape T28

◆ Continuous waterproofing;
◆ Ultra-thin;
◆ Good tensile strength;
◆ Highly self-fusing tape;
◆ Suitable for irregular shapes cable;
◆ Resistance to high/low temperature;
◆ Resistance to corrosion;
◆ Resistance to ozone, UV, xenon exposure;

COTRAN 930 Waterproof Insulation Tape

COTRAN 930 is made of fully vulcanized rubber as the base material, supplemented by one tacky mastic layers of waterproof. It can meet the wear-resistant, waterproof and needs of sheath repair for all types of cables. COTRAN 930 is used in heat shrink and cold shrink field to provide good waterproof, insulation and sealing as the cable joints accessories.

Heat Shrinkable Busbar Insulation Tube

Designed for insulation of copper and aluminum busbars- for electrical substations and switchgear cabinets. Can be used for exterior installations

Shrink ratio: 2.5:1

Operating voltage: 35 kV

Material: polyolefin, halogen-free «HF»

Analogs: BPTM (Raychem); BBI (3M)

Resistant to the phenomenon of tracking and UV radiation

High dielectric strength

Color: brick red

The use of tubes ТТШ allows shortening the distance between phase busbars and significantly reducing the dimensions of the device

Protects electrical busbars against chemical corrosion

Protects equipment from short circuits in case of contact of electrical devices with animals and birds

64/110KV YJZWGG Pre-Fabricated Dry Outdoor Termination For 64/110kv Xlpe Cable

Pre-fabricated dry termination is integrally composited of stress cone and silicone rubber insulation material.

Heat Shrink Rain Shed (10~36kV)

Applications：

Used to provide insulation protection for cable outdoor termination in order to increase the creepage distance and avoid the formation of sewage for various of rod supporting insulators.

Low Voltage Cast Resin Straight Through Joint

COTRAN cast resin joint kits are reliable jointing solutions for intermediate connectors of wires and cables. The cast resins without filler are high quality, and fast setting resin for tough ambient conditions. Ideal for power cable accessories as insulation or as protective layer in case of MV joints. The products have the advantages of excellent waterproof performance, convenient installation, excellent electrical performance and long-term immersion in water.