Wholesale Silicone Cold Shrink Tube With Mastic KC97,Silicone Cold Shrink Tube With Mastic KC97 Manufacturers

Silicone Cold Shrink Tube With Mastic KC97

◆ High elastic silicone rubber tube structure with mastic built-in, dual layers design can bring double guarantee of
◆ weatherproofing protection;
◆ IPX8 class, stable and long life during operation;
◆ Easy to install, only three steps (Cover, pull and clench);
◆ Fast installation, only 15-30 seconds needed to seal one connection
◆ No limitation of spare space, especially design for narrow space, high density connectors mounted equipment such as scenario of 3G and; 4G combination site, multi-band antenna), also convenient to deploy on wall-mounted, high tower, pole-mounted condition etc.,
◆ Easy to uninstall, only need knife to cut tube open and no sticky mastic left;
◆ No skill required by engineers, uniform quality after installation, stable and good sealing and weatherproofing performance;
◆ Much time cost, and labor cost saving;
◆ Perfect SWR performance approved by telecom operators;
◆ Good operating capability under extreme cold and hot condition, highland, salt-mist situation, heavy windy weather, and anti-UV, anti-ozone;
◆ Widely deployed for telecom projects wherever in China domestic and oversea;

Item		Parameter and Result	Test Method
Waterproof	Class	Pass, IPX8	IEC 60529:1989+A1:1999+A2:2013； 1 meter depth in water, duration: 4 hours
Physical and mechanical properties	Shore Hardness	A/41/1	ASTM D2240-15
	Tensile Strength	9.42 MPa	ASTM D412-15aMethod A
	Elongation	960%	ASTM D412-15aMethod A
	Tear Strength	41.6 KN/m	ASTM D624-00(2012)
	Excessive Mastic Test	Pass No excessive mastic	Pull out the support tube, and place sample at room temperature horizontally, after 72h, inspect whether the mastic excess or not
	Adhesion Test	Pass Built-in mastic was all attached on the inner wall of sample	Use sharp knife to cut sample open, then inspect whether the mastic attached on the inner wall of samples or not.
	Brittleness temperature by impact	Pass	ASTM D746-14，-60℃
	Drop test	Pass No damage, deformation, and support tube could be pulled out normally	Drop from height 1.2m on tile floor surface, 3 times to test
Flammability	Horizontal burning	HB	UL 94-2013 Rev.6-2016 Section 7
Electricity	Dielectric Strength	24.4 KV/mm	ASTM D149-09(2013) Method A
Performance under harsh environment	Mechanical and waterproof properties	No crack, discoloration, damage or deformation, IPX8 Pass	1. Dry heat test (IEC 60068-2-2:2008 Test Bb): 90±2℃，168 hours; 2. Low temperature test (IEC 60068-2-1:2008Test Ab): -40±2℃，168 hours； 3. Thermal cycling test: Cycle time:12h/cycle, Cycle index: 10 cycles, Total duration: 120 hours; 4. Damp heat test, cyclic test (IEC 60068-2-30:2005 Test Db)：Cycle time:24h/cycle, Cycle index: 10 cycles, Total duration: 240 hours; 5. Damp heat test, steady state (IEC 60068-2-78:2012 Test Cab)：Temperature: 75±2℃, Humidity：(95±1) %RH, Total duration: 1000 hours
Aging test	Light aging test-UV exposure	No crack, discoloration, damage or deformation Grey scale: 4-5 IPX8 Pass	ISO 4892-3:2016Cycle1& ISO 105-A02:1993/Cor.2:2005 Lamp type: UVA-340, 8h UV at (60±3)℃ BPT，0.76W/(m²×nm)@340nm 4h condensation at(50±3)℃ BPT Exposure duration:1000 hours
Aging test	Ozone aging	No crack, discoloration, damage or deformation, IPX8 Pass	ASTM D1149-16 Method B procedure B1 Temperature: 40±1℃ Ozone concentration:50±5 pphm Exposure duration: 72 hours
Material	Environmentalprotection	RoHS Reach	IEC 62321 SVHC
Temperature	Installation temperature	-40℃ - 60℃	Refer to “mechanical properties” and “performance under harsh environment”
	Operation temperature	-60℃ - 90℃
	Stock temperature	-60℃ - 90℃

Model	Color	Application	Package
KC97-DIN	Black, grey (color can be customized)	7/16 DIN connector to 1/2-inch jumper	50 pcs/carton
KC97-4.3-10	Black, grey (color can be customized)	4.3-10 connector to 1/2-inch jumper N type connector to 1/2-inch jumper	50 pcs/carton
KC97-7/8	Black,grey (color can be customized)	7/8-inchfeeder to 1/2-inch jumper	50 pcs/carton

Step 1
	1. Put jumper cable inside of the tube, before connectjumper to equipment 2. Arrow symbol will be direction of pulling strip, which usually should be downward
Step 2
	1. Hold the tube, pull stripdownward, and rolling,slowly by slowly 2. Whenpull the white strip till the plastic inner tube is horizontal alignment of the silicone rubber tube, hold cold shrink tube up and attached to bottom of connector on equipment, ensure the tube cover whole metal part of the connector. 3. Hold tube tightly to prevent tube moving, keep pulling strip downward, round and round, till all strip are out.
Step 3
	1. Hold the mastic part tightly, clench several times toaccelerate mastic attached on connector and jumper, help silicone rubber tube shrinking.
Remind	Pull Direction	Mount Position

Silicone Cold Shrink Tube With Mastic KC97

Silicone Rubber Cold Shrink Tube With Mastic en-KC97

Waterproof Silicone Rubber Cold Shrink Tube KC92